Protec 8" FRP Membrane Housing Pressure Vessels 1000 psi

Industry Leader in RO Expertise and Membrane Applications Since 1983™

Protec 8" 1000 PSI Fiberglass (FRP) Pressure Vessel Membrane Housings

The PROTEC™ Model PRO-8-1000-EP &PRO-8-1000-SP pressure vessels are designed for continuous use as housing for RO membrane filtration elements to purify typical seawater at any positive pressure up to 1000 PSI.

The PRO-8-1000-EP &PRO-8-1000-SP membrane housings will accommodate any make of eight-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the pressure vessel.

The Model PRO-8-1000-EP &PRO-8-1000-SP membrane housings have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped.

Design Pressure at 120ºF	1000 PSI	Operating pH Range	3-11
Minimum Operating Temp.*	20ºF	Cleaning pH Range (<30 min.)	2-12
Maximum Operating Temp.	120º	Application	Typ. Brackish Waters
Factory Test Pressure	1500 PSI	Feedwater TDS	≤ 45,000 ppm Max.
Burst Pressure	6000 PSI
*Please advise while ordering membrane pressure vessel if continuous operating temperature is less than 45ºF.

End Port Membrane Housing Pressure Vessels

Protec Vessel Model #	Old AMI Model No.	# of 8"x40" membrane elements per housing	Design Pressure	Vessel Length		Specification Sheets and Engineering Drawings	Image
Protec Vessel Model #	Old AMI Model No.	# of 8"x40" membrane elements per housing	Design Pressure	Inches	MM	Specification Sheets and Engineering Drawings	Image
PRO-8-1000-EP-1	PV8040PRO1000	1	1000 PSI	65"	1651
PRO-8-1000-EP-2	PV8080PRO1000	2	1000 PSI	105"	2667
PRO-8-1000-EP-3	PV80120PRO1000	3	1000 PSI	145"	3683
PRO-8-1000-EP-4	PV80160PRO1000	4	1000 PSI	185"	4699
PRO-8-1000-EP-5	PV80200PRO1000	5	1000 PSI	225"	5715
PRO-8-1000-EP-6	PV80240PRO1000	6	1000 PSI	265"	6731

Side Port Membrane Housing Pressure Vessels

Protec Vessel Model #	Old AMI Model No.	# of 8"x40" membrane elements per housing	Design Pressure	Vessel Length		Specification Sheets and Engineering Drawings	Image
Protec Vessel Model #	Old AMI Model No.	# of 8"x40" membrane elements per housing	Design Pressure	Inches	MM	Specification Sheets and Engineering Drawings	Image
PRO-8-1000-SP-1	PV8040PRO1000SP	1	1000 PSI	61.6	1565
PRO-8-1000-SP-2	PV8080PRO1000SP	2	1000 PSI	101.6	2581
PRO-8-1000-SP-3	PV80120PRO1000SP	3	1000 PSI	141.6	3597
PRO-8-1000-SP-4	PV80160PRO1000SP	4	1000 PSI	181.6	4613
PRO-8-1000-SP-5	PV80200PRO1000SP	5	1000 PSI	221.6	5629
PRO-8-1000-SP-6	PV80240PRO1000SP	6	1000 PSI	261.6	6645

For prompt, courteous and reliable service, contact us today!