Industry Leader in RO Expertise and Membrane Applications Since 1983™
Our Products Company Info Catalog Technical Site Contact Us Search How To Order



       

Protec 8" 300 PSI Fiberglass (FRP) Pressure Vessel Membrane Housings


The PROTEC™ Model PRO-8-300-EP & PRO-8-300-SP pressure vessels are designed for continuous use as housing for membrane filtration elements to purify typical brackish waters at any positive pressure up to 300 PSI.   The PRO-8-300-EP & PRO-8-300-SP membrane housings will accommodate any make of eight-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the vessel.

The Model PRO-8-300-EP & PRO-8-300-SP pressure vessels have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped.
 

  • Design Pressure at 120ºF

300 PSI

  • Operating pH Range

3-11

  • Minimum Operating Temp.*

20ºF

  • Cleaning pH Range (<30 min.)

2-12

  • Maximum Operating Temp.

120º

  • Application

Typ. Brackish Waters

  • Factory Test Pressure

450 PSI

  • Feedwater TDS

≤ 10,000 ppm Max.

  • Burst Pressure

1800 PSI

   

*Please advise while ordering if continuous operating temperature is less than 45ºF.

End Port Membrane Housing Pressure Vessels

Protec Vessel Model # Old AMI Model No.

# of 8"x40" membrane elements per housing

Design Pressure

Vessel Length Specification Sheets and Engineering Drawings

Image

Inches MM
PRO-8-300-EP-1 PV8040PRO300 1 300 PSI 61" 1549

Protec End Port FRP Membrane Housing Pressure Vessel
PRO-8-300-EP-2 PV8080PRO300 2 300 PSI 101" 2565
PRO-8-300-EP-3 PV80120PRO300 3 300 PSI 141" 3581
PRO-8-300-EP-4 PV80160PRO300 4 300 PSI 181" 4597
PRO-8-300-EP-5 PV80200PRO300 5 300 PSI 221" 5613
PRO-8-300-EP-6 PV80240PRO300 6 300 PSI 261" 6629

Side Port Membrane Housing Pressure Vessels

Protec Vessel Model # Old AMI Model No.

# of 8"x40" membrane elements per housing

Design Pressure

Vessel Length Specification Sheets and Engineering Drawings

Image

Inches MM
PRO-8-300-SP-1 PV8040PRO300SP 1 300 PSI 58.4" 1483

Protec Side Port FRP Membrane Housing Pressure Vessel
PRO-8-300-SP-2 PV8080PRO300SP 2 300 PSI 98.4" 2499
PRO-8-300-SP-3 PV80120PRO300SP 3 300 PSI 138.4" 3515
PRO-8-300-SP-4 PV80160PRO300SP 4 300 PSI 178.4" 4531
PRO-8-300-SP-5 PV80200PRO300SP 5 300 PSI 218.4" 5547
PRO-8-300-SP-6 PV80240PRO300SP 6 300 PSI 258.4" 6563



 

For prompt, courteous and reliable service, contact us today!


Home Contact Us How To Order
Back Up Next
150 PSI 300 PSI 450 PSI 600 PSI 1000 PSI 1200 PSI

Copyright © 2008 Applied Membranes, Inc. All Rights Reserved.