Industry Leader in RO Expertise and Membrane Applications Since 1983™
Our Products Company Info Catalog Technical Site Contact Us Search How To Order



       

Protec 8" 450 PSI Fiberglass (FRP) Pressure Vessel Membrane Housings


The PROTEC™ Models PRO-8-450-EP & PRO-8-450-SP pressure vessels are designed for continuous use as housing for membrane filtration elements to purify typical brackish waters at any positive pressure up to 450 PSI.  The PRO-8-450-EP & PRO-8-450-SP membrane housings will accommodate any make of eight-inch nominal diameter spiral-wound element as well as many hollow fiber elements. The element interface hardware for the specified element is supplied with the vessel.

The Models PRO-8-450-EP & PRO-8-450-SP Protec pressure vessels have been designed to meet the standards of the American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, Section X. At an additional cost, vessels can be inspected during fabrication by an ASME Authorized Inspector and Code stamped.
 

  • Design Pressure at 120ºF
450 PSI
  • Operating pH Range
3-11
  • Minimum Operating Temp.*
20ºF
  • Cleaning pH Range (<30 min.)
2-12
  • Maximum Operating Temp.
120º
  • Application
Typ. Brackish Waters
  • Factory Test Pressure
675 PSI
  • Feedwater TDS
≤ 10,000 ppm Max.
  • Burst Pressure
2700 PSI    

*Please advise while ordering membrane pressure vessel if continuous operating temperature is less than 45ºF.

End Port Membrane Housing Pressure Vessels

Protec Vessel Model # Old AMI Model No.

# of 8"x40" membrane elements per housing

Design Pressure

Vessel Length Specification Sheets and Engineering Drawings

Image

Inches MM
PRO-8-450-EP-1 PV8040PRO450 1 450 PSI 63" 1600

Protec End Port FRP Membrane Housing Pressure Vessel
PRO-8-450-EP-2 PV8080PRO450 2 450 PSI 103" 2616
PRO-8-450-EP-3 PV80120PRO450 3 450 PSI 143" 3632
PRO-8-450-EP-4 PV80160PRO450 4 450 PSI 183" 4648
PRO-8-450-EP-5 PV80200PRO450 5 450 PSI 223" 5664
PRO-8-450-EP-6 PV80240PRO450 6 450 PSI 263" 6680

Side Port Membrane Housing Pressure Vessels

Protec Vessel Model # Old AMI Model No.

# of 8"x40" membrane elements per housing

Design Pressure

Vessel Length Specification Sheets and Engineering Drawings

Image

Inches MM
PRO-8-450-SP-1 PV8040PRO450SP 1 450 PSI 58.7" 1491

Protec Side Port FRP Membrane Housing Pressure Vessel
PRO-8-450-SP-2 PV8080PRO450SP 2 450 PSI 98.7" 2507
PRO-8-450-SP-3 PV80120PRO450SP 3 450 PSI 138.7" 3523
PRO-8-450-SP-4 PV80160PRO450SP 4 450 PSI 178.7" 4539
PRO-8-450-SP-5 PV80200PRO450SP 5 450 PSI 218.7" 5555
PRO-8-450-SP-6 PV80240PRO450SP 6 450 PSI 258.7" 6571


 

For prompt, courteous and reliable service, contact us today!


Home Contact Us How To Order
Back Up Next
150 PSI 300 PSI 450 PSI 600 PSI 1000 PSI 1200 PSI

Copyright © 2008 Applied Membranes, Inc. All Rights Reserved.